If you like solving tricky, tough questions from fields like engineering, polytechnic, ITI and B.Sc., then you can become an NK Guru and get paid for doing what you love.
1. Trade Introduction, Safety Precautions and First Aid
Types of Fitter
Safety Precautions while using Hand Tools
2. Skill Information
Important Tools and Instruments
Marking, Measuring, Holding and Checking Tools
Common Faults of Gas Welding
Layout of Fitting Shop
Uses of Various Tools
Using Number Punch
Sheet Metal Tools
Some Important Operations
3. Trade Operations - I
Marking, punching, hacksawing of metals having different cross-sections and holding the job in vice.
To practice hacksawing operation on the pipe and channel.
To practice channel filing and parallel filing.
To practice marking with steel rule and odd leg caliper.
Marking off straight lines and arcs using scribing block and divider.
Chipping flat surfaces along a marked line.
To practice measuring, marking, punching, sawing and filing using try square.
To practice the drilling and checking of marked plates of different shapes.
To determine the center of round rod with the help of surface gauge and ‘V’ block.
To practice marking, sawing, chipping, flat filing, chamfering and checking.
To practice angular and radius marking by filing.
To practice slot and oil groove chipping.
To practice various types of file step making up to ±0.25 mm accuracy.
To practice letter punch and number punch by forming concave and convex radius.
To convert round rod into square rod by forging..
To change round rod into hexagonal rod by forging.
To practice the marking on sheets and cutting in straight line.
To practice marking of curve and cutting with snip.
To prepare various sheet metal joints
To mark rectangular tray and flaps soldering-I.
To practice rectangular tray and flaps soldering-II.
To assemble ash tray.
To prepare lap joint by brazing process.
To practice 'T' joint by brazing.
To practice straight cutting by hand gas cutting.
To prepare the fusion runs with filler rod.
4. Skill Information
Uses of Different Tools
Use of Punch
Tools and Instruments
5. Lathe Machine
Parts of the Lathe Machine
Lathe Machine Attachements
Lathe Machine Operations
Various Angles of the Lathe Cutting Tools
6. Trade Operations - II
To hold the job in a four jaw chuck and do facing operation on both the ends using knife tool.
To measure the diameter using the steel rule and outside caliper.
To do facing, turning and chamfering operation on the job, holding it in a three jaw chuck.
To practice plain and taper turning, reducing and checking.
To practice single edge step turning.
To practice double edge step turning.
To practice turning and taper turning operation to make a 'B' slot and form the mandrel, and practice knurling operation.
To practice drilling, turning, boring and brush step boring on the job and recess cutting.
Cutting the’ V’-groove on the lathe machine using a taping die and matching the nuts and bolts.
Drilling through holes and filing the radius and the surface of the MS flat job with complete accuracy.
To file the radial and conical surfaces with an accuracy of ±0.05 mm and fitting the radial and conical Workpieces.
To practice double square and radius fitting.
To practice square fitting, drilling and tapping.
To practice straight fitting.
To practice the triangular fitting.
To practice radius and angular fitting.
To make bracket while doing marking, bending, filing, drilling, riveting and checking alignment using try square.
To practice drilling and tapping.
To practice the universal state of holes and checking it while marking, filing, drilling, taping, drawing and stud fitting.
To practice counter sinking, counter boring and reaming.
To practice filing and scraping on the bearing surface with accuracy.
To practice external and internal radial and angular fitting.
Prepare the ± 0.04 mm dovetail sliding using lower pin and screws.
To prepare parallel and angular matching, thread cutting and sliding fit by using die with precision of ± 0.04 mm.
To assemble the parts of a machine.
To repair the parts of the machine.
Setting up of the arc welding plant and practicing arc striking.
Welding the MS sheet using the filler rod or without using the filler rod as shown in the drawing.
Making a bid in a straight line from a 10 mm thick mild steel plate placed in a flat position as given in the drawing.
Making a square butt joint using the butt weld from the MS sheet in a flat state.
To make the fillet weld (external corner joint) with a 3.5 mm mild steel sheet in a flat state according to the given drawing.
7. Trade Operations-III
To practice triangular internal fitting.
To practice hexagonal rod fitting.
To make key and key ways on the shaft and fitting.
To make a V-groove and slot.
To make lap riveted joints.
To make butt riveted joints.
To practice drilling on the cylindrical surface.
To practice scraping on the flat surface.
To practice scraping on the curved surface.
To practice scraping on the internal and angular surfaces.
To prepare the assembly fitting of the dowel pin and the screw.
To make a ± 0.02 mm sliding assembly using dowel pins and tap screw.
To practice sliding fitting.
To practice angular or radius marking through filing.
To practice radius and straight step fitting.
To practice triangular and slot fitting.
To practice angular fitting.
To practice dovetail fitting.
To drill blind hole and through hole in the 'Y' fitting at certain angle.
To practice tapping, reaming, counter sinking, counter boring and checking.
To practice hexagonal fitting.
To practice chamfering, drilling, tapping and internal fitting.
To make a snap gauge with an accuracy of ± 0.2 mm.
To practice radius fitting.
To make centre gauge.
To practice internal diamond fitting.
To practice the spark test to determine the amount of carbon in steel.
8. Trade Operations - IV
To practice 'H' fitting.
To practice hand lapping of gauges.
To practice hand reaming and fitting of taper pin, dowel pin, stud pin and bolt.
To prepare the jig for drilling.
To prepare 'V' block.
To manufacture the adjustable wrench.
To practice the pipe bending by hot/cold method.
To cut the pipe using hacksaw.
To practice the assembling of G.I pipe with standard pipe fitting.
To service the gate valve assembly.
To assemble the water tap.
To service the globe valve assembly.
To service the non-return valve assembly.
To do maintenance of the fire extinguisher.
To refill the fire extinguisher.
To perform screw cutting and straight fitting.
To study the manufacturing of tempering spring.
To practice the tempering of spring.
To practice the marking, cutting and drilling of stainless steel plate or aluminum metal without damaging the respective objects.
To practice drilling and tapping on the brass and copper jobs.
To fit the pulley on shaft and replace the damaged key with the new key.
To repair and replace a damaged belt.
To repair the broken gear teeth by the pegging and dovetail processes.
To prepare a packing gasket from rubber or fiber sheet.
To prepare the gasket packing using a hollow punch.
To form various knots using ropes and removing the damaged ropes.
9. Viva Practice
Like our books? Write a review!